lintec - Minimize your handling and loading costs. suomi
Mainpage
Mobile loading bridges
Rising levels
Container bridges
Loading ramps
Dock plates
Wheelchair ramps
AF Electric trucks
Trailer safety jacks
References
Contact us
Company
Lindqvist Oy Lintec
Toikansuontie 17
53500 Lappeenranta
Finland
Tel. +358 5 416 1701
Fax. +358 5 416 1715

www.lintec.fi
lindqvist oy lintec

trade reg. no. 390.154
vat. reg. no. FI06495948

Aluminium wheelchair ramps
wheelchair ramps Aluminium wheelchair ramps
SBA SBS SBK BTR ABS RAS RLK RRD AOL-R
Examples of use
Type selection

Type SBA
kynnyssilta This two part threshold ramp can be used for different heights. They are lightweight and easy to handle.

SBA bridge is not self supporting and must rest on the threshold.

Download brochure (only in finnish)

Type SBS
sbs SBS bridge ramps are designed as standard to span door steps or thresholds up to 35 mm high and 120 mm wide.

They are easy to handle, alternative dimensions are available on request.

Download brochure (only in finnish)

Type SBK
sbk SB-K entrance ramps have been designed to allow easy access over doorsteps. They have an anti-slip surface, and are maintenance free.

The height difference (dimension “h”) is needed when ordering.

Download brochure (only in finnish)

Type BTR
btr The BTR is a two piece threshold ramp, allow easy access to outside areas. The external section can be left in place, while the internal can be placed when required.

Download brochure (only in finnish)

Type ABS
pyörätuoliramppi This aluminium ramp offers an excellent balance between a very low weight and a high load capacity. Robust and easy to handle. These ramps are fabricated from an extruded profile which is cut to length and angled as required. With an internal width of 150 mm, and an overall width of 235 mm, these ramps are ideal for wheel chairs.

Their profile allows them to be stacked one inside the other for ease of storage, and the 45 mm high safety curbs on each side prevent any lateral slippage.

Download brochure (only in finnish)

Type ABS-F
pabsf A folding version of the ABS is available for ease of storage and use.

Download brochure (only in finnish)

Type ABS-Z
pabsz In case of small luggage space, the three times foldable ABS ramps are an ideal solution. They are fabricated from an extruded profile and offers an excellent balance between low weight and capacity.

With an internal width of 150 mm, they are also ideal for wheelchairs with offset axles.

Download brochure (only in finnish)




Back to Top

Type RAS
ras The loading ramps, type RAS are fabricated From a high strength aluminium alloy. The running surface is covered with an anti-slip coating.

Download brochure (only in finnish)

Type RAS-F
rasf The loading ramps, type RAS-F are fabricated from a high strength aluminum alloy. The running surface is covered with an anti-slip coating. A folding version of the ABS is available for ease of storage and use.

Download brochure (only in finnish)

Type RAS-W
rasw These ramps can be permanently installed inside the vehicle. The ramps pivoting and sliding mechanism uses ball bearings for ease of use. During transport the ramps are maintained vertically inside the vehicle by the safety straps supplied. If required, the ramp surface can easily be renewed with an anti-slip adhesive.

Each pair of ramps is supplied With a mounting kit.

Download brochure (only in finnish)

Type RLK
pyörätuolisilta This aluminium ramp is designed to allow for easy one man operation. The folding and unfolding of the ramp is made effortless by the use of gas struts to balance the weight of the ramp.

The ramp surface is fabricated from extruded aluminium profiles which are perforated and embossed to give a perfect anti-slip surface, and also allow rain and snow to disperse very easily. The light weight of the ramp allows most of the initial loading capacity of the vehicle position by two latches, and mounting blocks are used to maintain the assembly rigid and prevent any vibration during transport.

Download brochure (only in finnish)

Type RLK-Z
rlkz Derived from the RRK ramp. The RLK-Z is designed for use in vehicles with a low roof height. Folding twice in three sections the RLK-Z is made for easy installation and easy use. This aluminium ramp is designed to allow for easy one man operation. The folding and unfolding of the ramp is made effortless by the use of gas struts to balance the weight of the ramp.

Download brochure (only in finnish)

Type RRD
prrd Another version of RLK-ramp is type RRD. Basically the same ramp but with the facility to swivel back against the side panels of your van.

An optional locking latch is available to keep the unit in the swivelled position.

Lisävarusteena tilattavissa lisälukituslaite sisälle sivulle lukitsemista varten.

Download brochure (only in finnish)

Type AOL-R
pyörätuoliluiska The wheelchair ramp AOL-R is made to bridge over stairs or high steps.

The surface is fabricated from extruded aluminium profiles which are perforated and embossed to give a perfect anti-slip surface and allow rain and snow to disperse very easily.

Download brochure (only in finnish)





Back to Top